日本无码中出在钱,欧美一级成人网站,黄色毛片免费看片,五区六区久久久久,日韩美女永久网址在线观看

第一，就是加工的環境，精密平面磨床同一工作場地附近是不可能放置諸如沖床，Q420C高強板車床等震動較大的機床，容易引起共震，如何判斷是否有共振？停掉磨床，開動沖床或車床，如果手去觸摸磨床有震動或麻手感覺就是影響到了。所以必須要分開車間放置。

First, is the processing environment, near the same precision surface grinder work site is impossible to place such as punching machine, Q420C high strength plate lathe machine vibration, easy to cause a total shock, how to judge whether there is a resonance? Stop the grinding machine, start the punch or lathe, if the hand to touch the grinder with vibration or hemp hand feeling is affected. So it is necessary to separate the workshop.

第二，檢查地面，如果機床地腳螺絲水平沒調好，就會引起機床的共振。因為有時加工場地地面平整度不是很好，所以要通過調節水平螺絲來讓機床達到一個平整的高度。通過擰緊地腳螺絲，讓所有的地腳螺絲都緊貼著實地。

Second, check the ground, if not adjusted the level of machine screws, it will cause the resonance of machine tool. Because sometimes the surface roughness of the processing site is not very good, so to adjust the level of screws to allow the machine to achieve a level of height. By tightening the anchor bolts, anchor bolts for all are close to the field.

第三，如果上述動作做完后，震動仍未消除，就應檢查是否由于地面地板太空虛所至，如果地面是水磨石或者鋪的地板塊就相對結實，如果是水泥地平，地面就很虛會引起共振，碰到這種情況如何處理呢？可以去橡膠五金店買幾塊黑色橡皮膠墊，厚度6-10毫米左右，大小10公分和地腳墊尺寸稍大點就行，松開地腳螺絲，把橡皮膠墊墊在水平地腳墊下面，就可以起到很大的減震功能了。

Third, if the action is done, vibration have not been eliminated, it should check whether the ground floor to empty because, if the ground is terrazzo floor block or shop is relatively strong, if it is a virtual ground cement ground will cause resonance, encountered such a situation such as how to deal with? You can go to the hardware store to buy a few pieces of black rubber rubber pad, the thickness of 6-10 mm, the size of 10 cm and foot size slightly larger point on the line, loosen the anchor bolts, the rubber pad in the horizontal foot, you can play a big damping function.

第四，如果Q420C高強板車床震動仍未消除，可以換個砂輪試試，如果是法蘭沒有經過效平衡塊校正就把平衡塊裝上去了，那就拆掉平衡塊裝上去，不行就換個新法蘭試試，一般問題就解決了。

Fourth, if the Q420C high strength plate lathe vibration have not been eliminated, can change the wheel to try, if there is no effect after correction of the balance block balance block up flange, then removed the balance block up, not to change the new flange to try, you have resolved the problem.

第五，如果進行上述一系列動作仍未能消除震動那可能就不是你能處理的范疇了，有可能是磨床主軸時間用長了本身震動，里面軸承或馬達壞了，也有可能是Q420C高強板生產機床的結構及裝配有問題，這時就要通知廠家來處理了。

Fifth, if the above a series of actions failed to eliminate vibration may not be that you can handle the category, there may be a long time with the spindle vibration, inside bearing or damaged motor, there may be a structure and assembly of Q420C high strength plate production machine has a problem, then we must notify the manufacturer to the treatment.

本文由濟鋼一級代理商為您提供，我們的網站是：http://www.ctmpfsc.com我們將以全心全意的熱情為您提供更優質的服務，歡迎您的訪問！

This paper consists of Jinan level agents to provide you, our website is: http://www.ctmpfsc.com we will provide higher quality service to serve the enthusiasm for you, welcome your visit!